Remove the conversion step .tex -> .texi.

[cln.git] / INSTALL

diff --git a/INSTALL b/INSTALL
index 329d20a9d64298a90c9e9e95265d0d94a6d7d093..ea91d4ee670d1a670b8af9abf213ec9295ab9742 100644 (file)
--- a/INSTALL
+++ b/INSTALL
@@ -11,29 +11,29 @@ $ make install
 You need GNU make. On HP-UX, you also need GNU sed.
 
 Known to work with:
-  - Linux/x86, gcc-2.95.x, gcc-3.0(pre)
-  - Linux/ia64, gcc-2.96, gcc-3.0(pre)
-  - Linux/arm, gcc-2.95.3
-  - Linux/sparc, gcc-2.95.3
-  - Linux/alpha, gcc-2.95.x
-  - Linux/powerpc, gcc-2.95.x
-  - Solaris 2.4 (sparc), gcc-2.95
-  - OSF/1 V4.0 (alpha), gcc-2.95
-  - Irix 6.5, gcc-2.95.x
-  - BeOS, gcc-2.95.x
-
-The "make" step takes about 1 hour, on a P-II / 400 MHz / 64 MB.
-
-If you use g++ gcc-2.95.x or gcc-3.0, I recommend adding "-fno-exceptions" 
-to the CXXFLAGS. This will likely generate better code.
-
-If you use g++ from gcc-2.95.x on Sparc, add either "-O", "-O1" or
+  - Linux/x86, gcc-3.x, gcc-4.[0-2].x
+  - Linux/x86_64, gcc-3.[3-4], gcc-4.[0-2].x, gcc-4.3.0
+  - Linux/ia64, gcc-3.[2-4], gcc-4.[0-2].x
+  - Linux/arm, gcc-3.[0-3] (*), gcc-4.[0-2].x (*)
+  - Linux/mips, gcc-3.3, gcc-4.[0-2].x
+  - Linux/sparc, gcc-3.[1-3], gcc-4.[0-2].x
+  - Linux/alpha, gcc-3.[0-3], gcc-4.[0-2].x
+  - Linux/powerpc, gcc-3.[0-3], gcc-4.[0-2].x
+  - Linux/hppa, gcc-4.2.x (*)
+  - Solaris 2.4 (sparc), gcc-3.[1-3], gcc-4.[0-2].x (*)
+  - OSF/1 V4.0 (alpha), gcc-3.1
+  - Irix 6.5, gcc-3.0
+
+(*) On these platforms, problems with the assembler routines have been
+reported. It may be best to add "-DNO_ASM" to CPPFLAGS before
+configuring.
+
+Using gcc-4.2, the "make" step takes about 15 minutes, on an x86_64 / 2 GHz.
+
+If you use g++ from gcc-3.0.4 or older on Sparc, add either "-O", "-O1" or
 "-O2 -fno-schedule-insns" to the CXXFLAGS. With full "-O2", g++ miscompiles
-the division routines. If you use g++ older than 2.95.3 on Sparc you should
-also specify --disable-shared because of bad code produced in the shared
-library. Also, on OSF/1 or Tru64 using gcc-2.95.x, you should specify
---disable-shared because of linker problems with duplicate symbols in shared
-libraries.
+the division routines. Do not use gcc-3.0 on Sparc for compiling CLN, it
+won't work at all.
 
 More detailed installation instructions can be found in the documentation,
 in the doc/ directory.